Carboline Carbozinc 858

A two component zinc filled, cross-linked epoxy primer by Carboline.

Available in 5 and 10 Litres

* These colours are for guidance only. Variations between output devices can misrepresent the appearance of an actual colour. Also, we strongly advise that you order your complete paint requirements simultaneously to ensure a uniform batch colour.

2. Size

3. Select a Qty

As low as:

£190.58

Inc VAT £228.70

PRODUCT DETAILS

Carboline Carbozinc 858 is a high solid, organic zinc epoxy primer designed for corrosion protection of structural steel in salt and weathering environments.

Best Uses

Carboline Carbozinc 858 is easy to apply and protects steel galvanically by providing a tough and abrasion resistant film.

Outstanding application properties
Protects steel galvanically
Cures at low temperatures down to 2°C
Cured film is tough and abrasion resistant
Widely used within petrochemical-, offshore shipping- and other heavy industries in severe environments with appropriate topcoat
No induction time
Standard SSPC-Paint N° 20 Type II Level 1
Prequalified in accordance with NORSOK M-501, Rev.6 System 1.
N.B. an applied film of 90 microns DFT of Carbozinc 858 achieved accredited test certification for NORSOK M-501, Rev 4 System 1.

Application

Preparation
General Surface: Must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.
Steel Surface: Preparation to be minimum St 3 (ISO 8501-1). Alternatively, ultra high pressure water jetting to Nace No. 7 min. C Vis WJ-2 M Max. flash rust.

Application

Airless Spray: Pump ratio: 30:1 (min.), GPM Output: 3.0 (min.), Material Hose: 3/8 inch I.D. (min.), Tip Size: 0.017-0.021 inch, Output PSI: 2000-2200 (140-160 kg/cm²), Filter Size: 60 mesh
Brush & Roller (General): Recommended for touch up, stripe coating and hard-to-reach areas
Brush: Recommended using a soft bristle brush.
Roller: Generally not recommended for priming purposes

TECHNICAL

Approvals and Certifications

Standard SSPC-Paint N° 20 Type II Level 1
Prequalified in accordance with NORSOK M-501, Rev.6 System 1.
N.B. an applied film of 90 microns DFT of Carbozinc 858 achieved accredited test certification for NORSOK M-501, Rev 4 System 1.

Technical Info

Components:	Two Pack
Type:	Zinc Filler, Cross Linked Epoxy
Finish:	Flat
Stock Colours:	Bluish Grey, Green
Tintable:	No
VOC Content:
Volume Solids:	65%
Suitable Substrates:	Metal, Steel
Application Method:	Airless Spray, Brush
Theoretical Coverage:	13 m2 per litre at 50 μm 4.3 m2 per litre at 150 μm Allow for loss in mixing and application.
Wet Film Thickness (WFT):	80 - 230 μm per coat
Dry Film Thickness (DFT):	50 - 150 microns (1.95 - 5.9 mils) per coat
Induction Time:	-
Pot Life:	4 hours at 24°C and longer at lower temperatures
Touch Dry:
Overcoatable:	5 hours at 10°C
Fully Cured:	5 days at 10°C
Cleaner / Thinner:	Use Carboline Thinner #2 or Acetone
Shelf Life:	Part A: 9 months (24°C) Part B: 2 years (24°C)
Packaging:	Available in 5 and 10 Litres